Difference between revisions of "Krafft Points, Critical Micelle Concentrations, Surface Tension, and Solubilizing Power of Aqueous Solutions of Fluorinated Surfactants"

From Soft-Matter
Jump to: navigation, search
(Experimental Method)
Line 19: Line 19:
  
 
To measure Krafft Point and CMC: Krafft point was determined by the abrupt increase in the electrical conductivity of as a function of temperature
 
To measure Krafft Point and CMC: Krafft point was determined by the abrupt increase in the electrical conductivity of as a function of temperature
 +
 +
CMC: measured by the electrical conductivity-concentration curve at constant temperature
 +
  
 
Surface Tension Measurements: [(described in another paper)][http://pubs.acs.org/doi/pdf/10.1021/j100650a021]  
 
Surface Tension Measurements: [(described in another paper)][http://pubs.acs.org/doi/pdf/10.1021/j100650a021]  
Line 24: Line 27:
 
A drop-weight method was used to measure surface tension. This method involves obtaining an image of a drop and comparing its shape and size to theoretical profiles. Once <math>\beta</math> and b have been determined from shape and size comparisons, the surface tension is calculated from:  
 
A drop-weight method was used to measure surface tension. This method involves obtaining an image of a drop and comparing its shape and size to theoretical profiles. Once <math>\beta</math> and b have been determined from shape and size comparisons, the surface tension is calculated from:  
  
[[Image:Eqn.png]]
+
[[Image:surface.png]]
  
 
The reason this is a viable method is, the shape of an axisymmetric pendant or sessile drop (see figure below) is only dependent on the Bond number (a measure of the relative importance of gravity to surface tension in determining the shape of the drop). For drops with Bond numbers near zero, surface tension dominates and the drop is close to a sphere in shape. For drops with larger Bond numbers, the drop becomes increasingly deformed by gravity.  
 
The reason this is a viable method is, the shape of an axisymmetric pendant or sessile drop (see figure below) is only dependent on the Bond number (a measure of the relative importance of gravity to surface tension in determining the shape of the drop). For drops with Bond numbers near zero, surface tension dominates and the drop is close to a sphere in shape. For drops with larger Bond numbers, the drop becomes increasingly deformed by gravity.  
Line 32: Line 35:
 
==Results==
 
==Results==
  
Surfactants form micelles above the Krafft point and the solubility of surfactants in water increases drastically. Therefore, solubilization occurs above the Krafft point.  
+
Surfactants form micelles above the Krafft point and the solubility of surfactants in water increases drastically. Therefore, solubilization occurs above the Krafft point. The longer chain surfactants have low CMC's and are much more surface active (i.e. they are more efficient surfactants).
CMC: measured by the electrical conductivity-concentration curve at constant temperature
+
  
  

Revision as of 04:06, 26 October 2011

Krafft Points, Critical Micelle Concentrations, Surface Tension, and Solubilizing Power of Aqueous Solutions of Fluorinated Surfactants

Authors: Hironobu and Kozo Shinoba

Journal: The Journal of Physical Chemistry, Vol. 80, No. 22, 1976, p2468-2470


Introduction

This paper discusses the Krafft points, critical micelle concentrations (cmc), surface tension above the cmc, and solubilizing power in aqueous solutions of perfluoroalkane carboxylates as functions of fluorocarbon chain length.

The surface tension of these types of solutions is lower than that for ordinary surfactants. Fluorinated surfactants are very stable and have special industrial uses. The longer chain surfactants are more surface active and have high solubilization at low concentrations (compared to shorter chain surfactants). However, the Krafft point increases with increasing hydrophobic chain length. The Krafft point is the point above which ionic surfactants form micelles (and therefore dissolve well). Before this paper was published, it was shown that the kinds of [gegenions][1] affect the Krafft point. This paper outlines some results on the effect of the kinds of gegenions and chain length of surfactant on the Krafft point, surface tension, cmc, and solubilizing power in aqueous solutions of these perfluoroalkane carboxylates.


Experimental Method

Solutions of perfluoroalkane carboxylates with hydrocarbons of varying lengths were created.

To measure Krafft Point and CMC: Krafft point was determined by the abrupt increase in the electrical conductivity of as a function of temperature

CMC: measured by the electrical conductivity-concentration curve at constant temperature


Surface Tension Measurements: [(described in another paper)][2]

A drop-weight method was used to measure surface tension. This method involves obtaining an image of a drop and comparing its shape and size to theoretical profiles. Once <math>\beta</math> and b have been determined from shape and size comparisons, the surface tension is calculated from:

Surface.png

The reason this is a viable method is, the shape of an axisymmetric pendant or sessile drop (see figure below) is only dependent on the Bond number (a measure of the relative importance of gravity to surface tension in determining the shape of the drop). For drops with Bond numbers near zero, surface tension dominates and the drop is close to a sphere in shape. For drops with larger Bond numbers, the drop becomes increasingly deformed by gravity.

Bubble.png

Results

Surfactants form micelles above the Krafft point and the solubility of surfactants in water increases drastically. Therefore, solubilization occurs above the Krafft point. The longer chain surfactants have low CMC's and are much more surface active (i.e. they are more efficient surfactants).





Surf 1.png



Surf 2.png


Relation to Soft Matter