Controllable Microfluidic Production of Microbubbles in Water-in-Oil Emulsions and the Formation of Porous Microparticles

From Soft-Matter
Revision as of 16:16, 18 February 2009 by Zachwg (Talk | contribs) (Review Comments)

Jump to: navigation, search


The paper described the formation of micrometer gas-in-water-in-oil emulsions and the effects of liquid flow rates and gas pressure on the formation of water-encapsulated microbubbles. The effects of two different microfluidic geometries (flow-focusing and T-junction channels) and the addition of photopolymerizable monomers were investigated.

Experiment Setup

The method described in the paper is as follows: monodisperse microbubbles were generated in a continuous water phase using a flow-focusing geometry. Then, the gas-in-water system was detached into gas-in-water droplets by using a flow-focusing or T-junction geometries. They found that the double flow-focusing geometry’s (DFF) advantage is its ability of producing thin water shells while the T-junction geometry (FFT) allowed them control over the number of gas bubbles per water droplets. The addition of photopolymerizable monomers (acrylamide) into the aqueous phase allowed them to obtain porous polyacrylamide particle with lower elastic moduli compared to solid polyacrylamide particles.

Al1 1.jpg


Number of gas bubbles per droplets

By controlling the flow rate ratio of water to oil at constant gas pressure, they have found the different conditions that reproducibly give discrete numbers of gas bubbles per water droplets. By adjusting the gas pressure, they have also observed two different regimes, one where the number of gas bubbles per water droplets is independent of gas pressure (Qw/Q0=0.3-0.6) and another where the number of gas bubbles per water droplets is dependent of gas pressure (Qw/Q0=0.25-0.3, 0.6-0.9). When the flow rate ratio of water to oil is lower than 0.15 or higher than 1, the gas-in-water-in-oil emulsions didn’t form steadily and gives either a string of gas bubbles in a continuous water phase or water droplets with no bubbles at all.

The results of the variation of Qw/Q0 on the number of gas bubbles per droplets are shown below:

Al1 2.jpg

Thickness of the water layer

They noticed that even though the sizes of the bubbles were dependent on the relative flow rate (Qw/Q0), the sizes of the droplets did not depend significantly on Qw/Q0. This allowed them to control the thickness of the water layer. They also observed that the gas pressure played a minor role in the DFF while it significantly affected the droplet size in the FFT.

The dependence of thickness of the water layer on the relative flow rate for both DFF and FFT is shown below:

Al1 3.jpg

Addition of photopolymerizable monomers into the aqueous phase

By adding in photopolymerizable monomers (acrylamide) into the aqueous phase, they were able to fabricate porous particles by making droplets containing gas bubbles and then polymerizing the acrylamide. The effective elastic modulus of the dry photopolymerized polyacrylamide particles with and without entrapped microbubbles was then investigated using atomic force microscope. The result obtained is shown in the graph below:

Al1 4.jpg

Review Comments

- Figures are already described well in the text, so maybe leave out scanned figure captions

- I'm wondering about the error bars in Fig 3b--why might there be so much variation for 4 bubbles?

Scott's comments: Were there any scaling relationships found for the size of the drops relative to the 
flow rates of the fluids? If so, how did they scale?
What did you find the most interesting about this paper? What do you think could be the practical use of this method?--Lidiya 02:21, 18 February 2009 (UTC)

Sung Hoon's comment: The image in Fig. 4 (b) looks interesting. How did the shape form?

Zachwg's comment: I'm with Lidiya. Did the authors mention what kind of applications they think this technology might have? Could you trap living cells inside these bubbles rather than just gas?